SACC-DSI-FS-17CON-L180 SCO SH

https://www.phoenixcontact.com/in/products/1436806 Flush-type connector - SACC-DSI-FS-17CON-L180 SCO SH - 1436806 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Sensor/actuator flush-type connector, socket, 17-pos., M12 SPEEDCON, shielded, A-coded, rear/screw mounting with Pg9 thread, with straight solder pins     Key Commercial Data Packing unit 20 pc GTIN Weight per Piece (excluding packing) 14.995 g Custom tariff number 85366990 Country of origin Germany Technical data Dimensions Length of the solder pin 6 mm Ambient conditions Ambient temperature (operation) -25 °C ... 85 °C (Plug / socket) -40 °C ... 85 °C (without mechanical actuation) Degree of protection IP67 General Note The electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration. Rated current at 40°C 1.5 A Rated voltage 30 V Rated surge voltage 0.8 kV Number of positions 17 Insulation resistance ≥ 100 MΩ 02/02/2016   Page 1 / 5 https://www.phoenixcontact.com/in/products/1436806 Flush-type connector - SACC-DSI-FS-17CON-L180 SCO SH - 1436806 Technical data General Coding A - standard Standards/regulations M12 connector IEC 61076-2-101 Status display No Overvoltage category II Degree of pollution 3 Connection method Solder pins Insertion/withdrawal cycles > 100 Torque 3 Nm ... 4 Nm (Installation-side) Mounting type Rear mounting Pg9 With flat nut Material Flammability rating according to UL 94 V0 Contact material CuZn Contact surface material Au Contact carrier material PA 66 Material, knurls Zinc die-cast, nickel-plated Sealing material NBR Cable Ambient temperature (operation) -40 °C ... 85 °C (cable, fixed installation) -25 °C ... 85 °C (cable, flexible installation) Standards and Regulations Standard designation M12 connector Standards/regulations IEC 61076-2-101 Flammability rating according to UL 94 V0 Classifications eCl@ss eCl@ss 4.0 27250313 eCl@ss 4.1 27250313 eCl@ss 5.0 27143423 eCl@ss 5.1 27143423 eCl@ss 6.0 27143423 eCl@ss 7.0 27449001 eCl@ss 8.0 27440103 ETIM ETIM 3.0 EC002061 ETIM 4.0 EC002061 ETIM 5.0 EC002061 02/02/2016   Page 2 / 5 https://www.phoenixcontact.com/in/products/1436806 Flush-type connector - SACC-DSI-FS-17CON-L180 SCO SH - 1436806 Classifications UNSPSC UNSPSC 6.01 31251501 UNSPSC 7.0901 31251501 UNSPSC 11 31251501 UNSPSC 12.01 31251501 UNSPSC 13.2 31251501 Approvals Approvals Approvals EAC / cULus Recognized Ex Approvals Approvals submitted Approval details EAC  cULus Recognized      mm²/AWG/kcmil 26 Nominal current IN 1.5 A Nominal voltage UN 30 V Accessories Accessories Protective cap Screw plug - PROT-M12 - 1680539 An M12 screw plug for the unoccupied M12 sockets of the sensor/actuator cable, boxes and flush-type connectors     02/02/2016   Page 3 / 5 https://www.phoenixcontact.com/in/products/1436806 Flush-type connector - SACC-DSI-FS-17CON-L180 SCO SH - 1436806 Accessories Screw plug - PROT-M12 SH - 1503302 An M12 screw plug for the unoccupied M12 sockets of the shielded sensor/actuator cable, boxes and flush-type connectors     Screw plug - PROT-M12 FB - 1555538 M12 high-grade steel screw plug, for unoccupied M12 sockets of the sensor/actuator cables, boxes and flush-type connectors for the food industry     Seal Flat gasket - SACC-PG9-SEAL CLM - 1556320 Pg9 flat gasket for the rear mounting of M12 flush-type connectors with Pg9 fastening threads     Drawings Dimensional drawing max.4,5 1x45° 2 3 13 4 17 1 5 11 14 10 6 15 9 16 8 7 12 Ø15,3 +0,1 13,5 +0,1 Schematic diagram Pin assignment M12, 17-pos., socket side view Housing cutout for Pg9 fastening thread, mounting panel with feedthrough hole (alternatively with area as anti-rotation protection for panel thicknesses > 2 mm up to max. 4.5 mm) 02/02/2016   Page 4 / 5 https://www.phoenixcontact.com/in/products/1436806 Flush-type connector - SACC-DSI-FS-17CON-L180 SCO SH - 1436806 Drilling diagram Dimensional drawing 18 9x33° 3 14 6 Ø1,2 5 Ø1,1 PG9 2 13 15 7 6,5 Ø0,6 15° 16 11 12 17 Ø6,5 1 10 9 8 Ø14,6 45° 6x6 0 ° Ø3,25 5,5 4 Ø0,7 +0,05 17 18 M12 flush-type connector Dimensional drawing 18 6, 8 6, 6 45° M12 front view Phoenix Contact 2016 © - all rights reserved http://www.phoenixcontact.com 02/02/2016   Page 5 / 5